The Check User Space Spelling command checks for misspelled words in
the first 32,000 bytes of a user space. The data in the user space
would be considered as a string with blanks separating the words.
The dictionary supplied by TAA is used by default. Special
dictionaries may be named. See the discussion with the TAADCT tool.
2000 bytes segments are handled. If a word splits over two segments,
it will probably be considered an error.
A typical command would be:
CHKSPCSPE USRSPC(xxx)
The first 32,000 bytes of the user space would be checked using the
TAADFT dictionary. One line would be listed for each word not found
in the dictionary. If any words are listed, the spooled file would
be displayed by default.
No indication of where in the user space the bad words exist is
shown. Use DSPUSRSPC and the scan value field (with F16) to scan for
where the words exist.
If no errors were found, the command completes normally and the
spooled file would be deleted.
CHKSPCSPE escape messages you can monitor for
---------------------------------------------
TAA9893 One or more words in error were found.
Escape messages from based on functions will be re-sent.
CHKSPCSPE Command parameters *CMD
----------------------------
USRSPC The qualified name of the *USRSPC object to be
checked. The library value defaults to *LIBL. A
specific library or *CURLIB may also be used.
ERRACTION How to handle spelling errors. If no spelling
errors exist, the spooled file is deleted.
*DISPLAY is the default to display the spooled file.
The spooled file is deleted after it is displayed.
*ESCAPE may be specified to send the TAA9893 message
as an escape type. The spooled file is retained.
*COMPLETION may be specified to receive a completion
message. The spooled file is retained.
DICT The name of a specific dictionary to be used. *DFT
is the default in which case the DCTARA parameter
takes precedence.
A specific dictionary name may be used along with a
library qualifier. If a specific dictionary is
named, DCTARA(*DFT) must be used.
DCTARA An optional parameter that allows a list of
dictionaries to be specified by naming a data area
in library TAADCT that contains the list. The
default is *DFT. The list of dictionaries must be
entered according to the CRTDCTARA TAA Tool and the
data area containing the dictionaries must exist in
the TAADCT library. Up to 8 dictionaries may be
named in the data area.
If *DFT is specified, the following rules exist:
1) If the library TAADCT does not exist, the TAADFT
dictionary in TAATOOL is used.
2) If the TAADCT library exists, a data area by the
name of the user of the job is searched for in
TAADCT. If it does not exist, a data area by the
name of SYSTEM is searched for in TAADCT.
3) If neither data area exists the TAADFT dictionary
in TAATOOL is used.
Restrictions
------------
Only the first 32,000 bytes are checked.
2000 bytes segments are handled. If a word splits over two segments,
it will probably be considered an error.
Prerequisites
-------------
The following TAA Tools must be on your system:
CHKOBJ3 Check object 3
CHKSPELL2 Check spelling 2
EDTVAR Edit variable
RSNLSTMSG Resend last message
RTVUSRSPC Retrieve user space
RTVUSRSPCA Retrieve user space attributes
RTVSYSVAL3 Retrieve system value 3
SNDCOMPMSG Send completion message
SNDESCINF Send escape information
SNDESCMSG Send escape message
SNDDIAGMSG Send diagnostic message
Implementation
--------------
None, the tool is ready to use.
Objects used by the tool
------------------------
Object Type Attribute Src member Src file
------ ---- --------- ---------- ----------
CHKSPCSPE *CMD TAASPCU QATTCMD
TAASPCUC *PGM CLP TAASPCUC QATTCL
TAASPCUR *PGM RPGLE TAASPCUR QATTRPG
|
